Right burner sparked endlessly without ever lighting, of course right as we started cooking for guests. Igniter had drifted out of position. Adjusted, caught on the very next attempt.
Wolfgang E.
A burner refusing to catch, or one stuck at full blast, both usually trace to one small part before anything bigger gets involved.
Open any of these for a plain explanation of what's usually going on.
You hear clicking or see sparks but the gas never actually ignites, sometimes with a faint smell that clears once you release the knob. An igniter out of position is common, or a clogged orifice keeping the spark from ever reaching the gas. Cleaning and realigning the igniter solves most of these before the valve's ever touched.
No matter where the dial sits, one burner just keeps running at maximum, even turned down or off entirely. This points toward a stuck infinite switch for that burner, not the heating element itself. We confirm the switch under load before swapping anything, the element is almost always fine.
A steady, rapid click continues without the burner ever lighting, sometimes for well over a minute. Moisture or built-up grime inside the igniter module usually explains it, blocking a clean, consistent spark. We clean and test the module before considering replacement.
A single element never warms up at all while every other burner works exactly as expected. A break somewhere inside that coil is the typical cause, visible once removed and inspected properly. We replace it directly, since a broken coil can't really be repaired in place.
Turning the knob produces no click and no resistance at all, it just spins past every marked position. A worn spring inside the knob assembly is the usual reason, unconnected to the burner or gas valve underneath. Typically one of the more affordable fixes we do.
Rather than a tidy, even blue circle, the flame comes out yellow or burns unevenly around the ring. Airflow choked off by a partially blocked port is a frequent explanation, worth ruling out before jumping to a bigger conclusion. Clearing the ports and running a fresh test comes well before recommending a complete burner swap.
Still Not Sure What's Wrong?
A quick call gets you a real answer, most jobs are wrapped in a single stop.
We work on these every week, not just occasionally, so we know what usually fails.
Codes vary by brand, but these patterns show up across most major stove and range manufacturers.
A temperature sensor on an electric or induction model is misreading.
Overheating protection has kicked in and shut things down.
An irregularity in incoming voltage has been detected.
Communication fault between the control board and panel.
A fault has been logged in a burner or element circuit.
Power cut out briefly, a reset usually clears this.
Since every brand assigns these codes a little differently, use this as a rough starting point rather than an exact match to your owner's manual. If the same code shows up again after cutting power for a minute, get a technician out to read it correctly.
What customers said after we sorted out their stove.
A few stove complaints trace back to something small worth checking yourself, no tools required.
Clean The Burner Ports
Spills and debris clog the small holes gas passes through, a soft brush clears light buildup safely.
Confirm The Knob Clicks In
Confirm the dial genuinely stops on one of the marked positions instead of sitting between two of them.
Verify Gas Or Power Supply
On a gas model, verify the shut-off valve is open. On an electric model, check the breaker hasn't tripped.
Check Grate Alignment
For gas models, a grate that's not seated quite right can throw off how the igniter senses the burner.
Wipe The Igniter Clean
Grease collecting right at the tip weakens the spark output, a quick pass with a dry cloth usually solves it on the spot.
Check For A Tripped Breaker
After any storm in particular, double-check that the dedicated breaker for an electric stove hasn't flipped off.
Still acting up? Something deeper is probably going on. Have a technician take a look and we'll figure it out.
We'll Handle It
859+ jobs done, a 90-day warranty on every one, and a $0 diagnostic fee once you go ahead with the repair.
Give us a few details and expect a call back to confirm a time.
Thank You!
Your message has been sent successfully. We'll get back to you shortly.
Thank You!
Your message has been sent successfully. We'll get back to you shortly.
Prefer to talk it through? (972) 812-7786